| Cosmetic |
Installed Hood Struts |
0.25 |
| Cosmetic |
Installed Fixed Headlights (units immediately began to fog and were later replaced) |
1.5 |
| suspension |
Raised front end suspension |
2.5 |
| Cosmetic |
Installed Corbeau Seats |
3 |
| Cosmetic |
Installed Momo Steering Wheel and NRG Hubs |
2 |
| Cosmetic |
Install HID Headlights (HID's were switched with LED lights later) |
2 |
| Cosmetic |
Install LED Parking Lights |
0.75 |
| Maintenance |
Install Windshield Wiper Motors |
1.5 |
| General Electrical |
Install Airbag Light Resistor |
0.25 |
| Cosmetic |
Install LED Sidemarkers |
0.75 |
| Cosmetic |
Cut out front license plate brackets |
1.25 |
| Cosmetic |
Repair map lights on Rearview Mirror (repair was poorly done and didn't hold up) |
1 |
| Cosmetic |
Install LED reverse lights and license plate cover |
0.5 |
| Comfort and Safety |
Attempting to fit Roll bar |
4 |
| General Electrical |
Began wiring aux ACC fusebox and repaired previous aftermarket wiring |
1.5 |
| Monitoring |
Installed boost/vacuum gauge |
0.75 |
|
|
|
| General Electrical |
Finishing ACC fuse box install |
3 |
| Maintenance |
Oil change and magnetic oil plug install |
1.5 |
| Monitoring |
Install flush mount USB for tuner |
0.5 |
| Maintenance |
Diff fluid flush |
1 |
| Maintenance |
Transmission flush |
1 |
| Maintenance |
Clutch fluid flush |
1 |
| Cosmetic |
Tint 3rd brake light |
1 |
| Cosmetic |
Tint reverse lights and taillihts |
2.5 |
| Transmission |
Install clutch pedal return spring |
0.5 |
| Transmission |
Install MGW Shifter |
3.5 |
| General Electrical |
Installed constant 12v fusebox |
0.75 |
| Comfort and Safety |
Install passenger seat brey-krause lap belt mounts |
0.5 |
| Engine |
Catch can bracket fabrication |
1 |
| Engine |
Catch can install |
0.5 |
| Suspension |
Prothane front/rear swaybar bushings installed (Had to remove and reinstall due to not sanding off rust and due to lack of grease) |
2 |
| General Electrical |
Gas cap popper relocation |
0.5 |
| Cosmetic |
Red LED install for door controls and traction control (didn't like the red and converted to white) |
0.5 |
| Transmission |
Anti-Venom shift detent install |
0.75 |
| Monitoring |
Shift Light install |
1 |
| Monitoring |
Vacuum distribution block install |
1.5 |
| Cosmetic |
Initial engine bay cleaning |
1 |
| Engine |
PCV check valve replacement (no longer used after supercharger install) |
0.5 |
| Monitoring |
Installed Tee fitting to brake booster vaccum line and connected to vaccum distro |
0.5 |
| Comfort and Safety |
Install of roll bar |
8 |
| Comfort and Safety |
Install of driver side 6pt harness mount adapter |
1 |
| Comfort and Safety |
Painted and reinstalled roll bar |
3 |
| audio |
Ran speaker wire, RCA's, power/ground, and mounts for the 4 channel amplifier |
3 |
| audio |
Built speaker wire harness for amp and speakers |
2.5 |
| Engine |
Install spark plugs and wires |
1.5 |
| audio |
Install double din radio, mic, gps antenna, usb drives |
4 |
| audio |
Install front door speakers and modified adapter plates |
7 |
| cosmetic |
Removal of Sunvisors |
0.5 |
| Cosmetic |
Installed replacement headlights (units fogged again and were replaced with oem headlights) |
2.5 |
|
|
|
| Monitoring |
Installed wideband o2 sensor - ran through torque tube tunnel from interior (had to cut out when installing long tube headers) |
2.5 |
| General Electrical |
Ran 4ga wire from battery to power distro |
3 |
| audio |
Began Sub box build, radio bezel, and gauge pods |
5 |
| audio |
Bulkhead fiberglassing and sub box bondo (reverted back to original stand alone sub box without bulkhead integration) |
4 |
| audio |
Sub box sanding, radio bezel painting |
3 |
| audio |
Radio bezel sanding and painting |
4 |
| audio |
Radio bezel bondo work |
4 |
| General Electrical |
Installed new 4ga breaker fuse |
1 |
| audio |
Built amp box, completed edges of sub box |
4 |
| Monitoring |
Completed rooting of Pixel 2XL and mount bracket (total time over 1 month) |
5 |
| audio |
Install radio bezel gauge wiring harness |
2.5 |
| audio |
Build radio bezel gauge wiring harness |
3 |
| Engine |
Installed Hinson Motor mounts and trans mount |
5 |
| exhaust |
Third attempt to install long tube headers - failed due to drivers side header contacting bell housing |
4 |
| exhaust |
Second attempt to install long tube headers |
5 |
| Engine |
Replaced engine coolant temp sensor (broke during header install) |
0.25 |
| Cosmetic |
Painted valve covers black, cleaned bolts |
2 |
| audio |
Continued bondo'ing sub box and form fitting to center console (decided to go back to basic sub box) |
3 |
| exhaust |
First attempt at installing long tube headers |
3 |
| Monitoring |
Installed fuel pressure sensor for FPR gauge onto fuel rail |
0.5 |
| exhaust |
Completed long tube header install, notched bellhousing, reassembled engine bay |
7 |
| exhaust |
Heat wrapped and installed O2 sensor extensions |
2.5 |
| Engine |
Installed new oil dip stick tube and mounted to head (broke original one while installing headers) |
0.5 |
| audio |
Continued sanding sub box and amp rack unit |
1.5 |
| exhaust |
Welded in extension from resonators to x pipe |
3.5 |
| General Drivetrain |
Attempted to bleed brakes - failed without additional help |
1 |
| Brakes |
Replaced brake light warning sensor on brake proportioning valve (broke this when investigating brake issues caused by blocked return line) |
0.25 |
| Brakes |
DOT4 Brake fluid flush and removal of blockage in brake return line to proportioning valve |
5 |
| exhaust |
Investigation of rattling from new long tube header system |
2 |
| exhaust |
Realigned exhaust to stop contact at diff, trans tunnel, and heat shield |
2 |
| audio |
Additional bondo added to sub box / amp rack |
0.5 |
| Monitoring |
Installed trans temp sensor into trans drain plug - drilled through bulkhead and connected to gauge |
2 |
| Monitoring |
Ran fuel pressure sensor wiring through firewall and connected to gauge |
1 |
| General Electrical |
Rewired constant 12v fuse box |
0.75 |
| Suspension |
Sanded off rust on sway bar where bushings go. Repacked bushings with grease |
1 |
| Maintenance |
Realigned steering shaft back to factory position (accidentally spun steering shaft when it was disconected during header install) |
0.5 |
| cosmetic |
Installed DLR light housings |
0.75 |
| Maintenance |
Investigating rattle from headers - discovered bolt lodged between pipes near collector. Unable to remove (bolt fell during header install) |
1 |
| Cosmetic |
wrapped driver knee bolster in leather (wrap didn't hold up and unit was replaced by used black one) |
2 |
| Cosmetic |
wrapped lower driver door panel in leather (cut reflector hole too big) |
4 |
| Exhaust |
Extracted bolt lodged between driver long tube header pipes (bolt fell during header install) |
0.25 |
| Cosmetic |
Installed black passenger floor, driver floor, and waterfall carpets |
2 |
| Cosmetic |
White LED install for door controls and traction control |
0.5 |
| Cosmetic |
Completed carpeting trunk storage covers in black |
3 |
| Cosmetic |
Painted traction control bezel in metallic pewter |
1.5 |
| Cosmetic |
Painted radio bezel in metallic pewter |
1 |
| Cosmetic |
Painted trunk release / fog light bezel in metallic pewter |
0.5 |
| Cosmetic |
Installed black trunk floor carpet, black rear trunk side panels, black rear trunk center panel |
0.75 |
| Cosmetic |
Glued together knee bolster to trunk release trim bezel and installed |
1 |
| Cosmetic |
Installed new passenger door card |
0.5 |
| Audio |
Installed new 5-channel amp and sub box |
1.5 |
| Audio |
Completed sub box and wrapped with carpet |
1 |
| Cosmetic |
Installed new black driver's door card |
0.25 |
| Comfort and Safety |
Removed roll bar to Installed black OEM seat belts and black lower B-pillar trim |
4 |
| Comfort and Safety |
Installed black seat belt receivers to seats |
0.5 |
| Engine |
Removed steering rack, timing gears, alternator, valve covers, radiator, condensor, water pump, oil pump |
9.5 |
| Engine |
Cleaned timing cover and belt tensioner. Installed new cam, ls2 timing gears, acdelco water pump, melligs oil pump, crank seal, chromoly push-rods, radiator support bracket, harmonic balancer |
8.5 |
| Engine |
Continued install of valve springs |
1 |
| Engine |
Pinned Crank, finished valve spring install, installed rockers, reinstalled coils/plugs/wires, resintalled alternator, installed t-stat housing with gasket |
4.5 |
| Engine |
Welded bolt to frame for radiator support mounting. Installed power steering rack. Installed new moog tie-rod ends. Performed first start with new cam. |
5 |
| Engine |
Installed radiator, condensor, intake, and shrouds (along with various other small parts) |
4 |
| Engine |
Reinstalled front bumper and hood. Refilled R134/AC system. Refilled/bled power steering |
3.5 |
| Engine |
Installed new 80lb injectors and uploaded tune |
2 |
| Cosmetic |
Installed KnightDrive sleepy eye headlight modules |
4.5 |
| Cosmetic |
Primered and began painting new headlight lids |
1 |
| Cosmetic |
Completed painting headlight lids, installed new lid bracket, installed lids |
3 |
| Engine |
Installed new duralast starter |
6 |
| Cosmetic |
Completed Headlight bezel install and test fit new exhaust |
3 |
| Monitoring |
Installed differential drain plug adapter and temp sensor |
0.25 |
| Maintenance |
flushed diff fluid |
0.5 |
| Maintenance |
Completed oil change with Mobile 1 5w-30 and Mobile 1 Oil Filter |
0.5 |
| Comfort and Safety |
Installed sound deadening material to trunk and passenger floor |
3 |
| Comfort and Safety |
Replaced HVAC blower fan |
1 |
| Transmission |
Replaced clutch Master Cyclinder |
5 |
| Comfort and Safety |
Replaced Driver window regulator |
1 |
| Comfort and Safety |
Installed driver side window regulator |
1 |
| Engine |
Installed SC bracket and SC, fuel pump harness, fuel pump, FPR, diff temp sensor wire |
11 |
| Engine |
Installed innercooler, BOV, SC piping, built/ran braided fuel lines, cleaned injector ports, mounted fuel filter, |
12 |
| Engine |
Installed MAP sensor, tightened all fuel lines, routed all vacuum lines, mounted catch can, replaced spark plugs,ppp |
5 |
| Engine |
Completed fuel lines, grounded fuel pump harness, set FPR pressure, reassembled trunk, installed tank shields |
4.5 |
| Engine |
Routed and installed O2 sensor wiring, reassembled remainder of interior, repaired seat seatbelt passthroughs |
3 |
| Engine |
Installed all AN vacuum lines, Inspection/planning/diagramming of new PCV system, rerouted evap purge lines to atmosphere |
4 |
